Commercial Unit Turnover Cleaning Checklist for Mississauga and the GTA
Published: October 18, 2026 · 6 min read · By LowFare Maintenance Team
When a commercial tenant moves out, the unit has to be ready for the next one: clean, empty, and in a condition the landlord can show without apologising. In the GTA, where many offices, plaza units and industrial bays change hands every year, turnover cleaning is a routine job for property managers. It is also one of the easiest jobs to get wrong, because nobody writes down what “clean” means until the walkthrough goes badly.
This checklist is for landlords, property managers and outgoing tenants of commercial units in Mississauga and across the GTA. It covers what the lease usually controls, how to plan the work, and a room-by-room list you can hand to a cleaning contractor.
Start with the lease, not a generic checklist
Residential move-outs in Ontario are shaped by the Residential Tenancies Act. Commercial units are different. Ontario's Commercial Tenancies Act deals with matters such as rent and termination, but the condition a commercial unit must be returned in is set mainly by the lease itself. Most commercial leases have a “surrender” or “yield up” clause that says how the premises must be left: often broom-clean, sometimes with the tenant's fixtures removed and damage repaired.
Before any cleaning is booked, read three parts of the lease:
- The surrender or end-of-term clause, which sets the standard the unit must meet.
- Any clause about removing signage, fixtures, wiring or equipment the tenant installed.
- Any clause about repairs, painting or restoring the premises to their original layout.
“Broom-clean” is a low bar: floors swept, debris and personal property gone. Many landlords ask for more than that so the unit can be shown right away. If the lease only requires broom-clean, the landlord usually pays for anything beyond it. Agreeing this in writing before the move avoids arguments later.
Plan the order of work
Turnover cleaning goes faster and costs less when it is the last step, not one of the first. A practical order is:
- The outgoing tenant removes furniture, equipment, stock and personal property.
- Any removal of signage, cabling or tenant fixtures is done, as the lease requires.
- Repairs and painting are finished.
- The turnover clean is done, top to bottom.
- The landlord or property manager walks the unit with a checklist and signs it off.
If painting or repairs happen after the clean, dust and paint drips will undo part of the work and a second visit will be needed.
Room-by-room checklist for a commercial unit
Entrance and reception
- Entrance glass and door frames cleaned inside and out, including tape and sticker residue from old signage.
- Door hardware, push plates and closers wiped.
- Entrance mats removed or cleaned.
- Reception counters, ledges and baseboards dusted and wiped.
Open offices, private offices and meeting rooms
- Floors vacuumed; carpet extracted if stained or required by the lease.
- Hard floors swept, scrubbed and dried.
- Window sills, ledges and blinds dusted; dead insects removed from sills.
- Walls spot-cleaned where marks can be removed without damaging paint.
- Light switches, door handles and frames wiped.
- Vents and return-air grilles dusted.
Kitchens and lunchrooms
- Cabinets and drawers emptied and cleaned inside and out.
- Counters, backsplash and sink scrubbed.
- Fridge, microwave and dishwasher cleaned inside, if they stay with the unit.
- Floor scrubbed, including under movable appliances.
Washrooms
- Toilets, urinals and sinks cleaned and descaled.
- Partitions, walls and mirrors wiped.
- Dispensers emptied or left as the landlord prefers.
- Floor and grout scrubbed; floor drains checked.
Warehouse and industrial bays
- Floor swept and, where needed, machine scrubbed.
- Oil and spill marks treated so the slab is presentable.
- Debris, pallets and packaging removed by the outgoing tenant or arranged for removal.
- Dock areas and door tracks cleared of debris.
Retail units
- Storefront glass cleaned inside and out, including old vinyl lettering residue.
- Fitting rooms, display areas and stock rooms emptied and cleaned.
- Floors cleaned to suit the floor type; resilient floors may need a scrub and recoat or a full strip and wax.
Floors are usually the biggest decision
Floors are where turnover budgets go. Carpet tile may need extraction, or in worn areas, replacement, which is a landlord or tenant decision rather than a cleaning job. Vinyl composition tile (VCT) can often be brought back with a strip and wax. Sealed concrete in industrial bays usually just needs sweeping and machine scrubbing. Decide which of these the lease requires before booking, because it changes the price more than anything else on the list.
If the floors need refinishing, book it after painting and before the final detail clean. See our commercial floor waxing page for how strip and wax and scrub and recoat compare.
Vacant units still need attention
Units that sit empty while they are marketed collect dust, dead insects on window sills and marks from contractors. A light clean before each showing, or on a set schedule while the unit is listed, keeps it looking cared for. It is a small cost compared with the time a unit sits vacant.
Safety and products during turnover cleaning
Turnover cleaning in an empty unit is still work in a workplace. Under Ontario's Occupational Health and Safety Act, hazardous cleaning products fall under WHMIS 2015, which in Ontario is set out in Regulation 860. Containers must be labelled and a Safety Data Sheet must be available for each hazardous product. Ask your contractor for the SDS of the products they will use, especially if another tenant shares the building's ventilation.
When you hire for turnover work, ask for the same documents. Lowfare has WSIB clearance and commercial liability insurance, and our staff are police-checked; we supply both certificates with the quote or on request. Request a quote.
The Ontario Fire Code also requires exits and the routes to them to be kept clear. In multi-tenant buildings, carts, bins and debris from a move should never block shared corridors or exit doors, even for a short time.
What to give your cleaning contractor
- The lease's end-of-term standard, or the landlord's own written standard if it is higher.
- A floor plan or a walkthrough of the unit.
- The date the outgoing tenant will be fully out and the date the unit must be ready.
- Building rules: freight elevator bookings, loading dock times, garbage rooms and contractor sign-in.
- Who signs off the work, and how deficiencies will be reported.
With that information, a contractor can give a fixed quote and a realistic schedule instead of an estimate that changes on site.
Common turnover cleaning mistakes
- Booking the clean before the tenant has removed everything, so the crew works around boxes and returns later.
- Cleaning before painting or repairs, then paying for a second clean.
- Leaving old signage residue on storefront glass, which is the first thing a prospective tenant sees.
- Forgetting high areas: vents, light fixtures and the tops of partitions collect dust that shows in daylight.
- Not checking the washrooms' floor drains and fixtures, which can smell in a unit that sits empty.
- Assuming the landlord and the outgoing tenant agree on what clean means without writing it down.
Each of these adds a visit or delays the next lease. A short planning call before the move usually prevents all of them.
Sign-off: use the same checklist for everyone
The simplest way to avoid disputes is to use one checklist for the outgoing tenant, the contractor and the landlord. Walk the unit together, tick each item, photograph anything that is not acceptable, and agree who fixes it. Keep the signed checklist with the lease file.
Lowfare does not offer stand-alone turnover cleaning, but the heaviest parts of a turnover are services we do provide: carpet cleaning, strip and wax for resilient floors, post-construction cleaning after a fit-out, and pressure washing of storefronts and walkways. We clean commercial premises only.
Questions about your building? Call 647-250-9918 or see our strip and wax page.